Old electrical panel insurance trouble usually shows up as a letter. If your carrier has told you the panel has to go, you most likely have one of the panels insurance won't cover, and the letter already named it.
It usually arrives at renewal, or right after a four-point inspection, and it names a brand. Federal Pacific, Zinsco, Sylvania, Challenger. The first two share a record of the one failure that matters most. The breaker does not trip.
A breaker that will not trip is not a breaker
Every circuit in your house depends on the breaker being the weakest link on purpose. When a wire overheats or something shorts out, the breaker is supposed to open first and take the damage itself. That is the whole job. It is the reason the wire in your walls is allowed to be as small as it is.
On these panels it can fail to open. The mechanism jams or the contact behind it has gone bad, and current keeps flowing into wire that is already hot. Nothing trips, nothing clicks, and there is no second chance inside the device. The next thing that happens is inside the wall.
Federal Pacific Stab-Lok. The Consumer Product Safety Commission opened an investigation into Stab-Lok breakers in 1980, and its own testing confirmed that many failed certain UL calibration tests. It closed the case in 1983 without a recall and without ruling on whether the breakers were safe, saying the data it had did not establish a serious risk. In 2002 a New Jersey court found that Federal Pacific had "knowingly and purposefully distributed circuit breakers which were not tested to meet UL standards as indicated on their label." Hanover Insurance's guidance says millions of Stab-Lok panels went in between 1950 and 1985, and we still find them in houses around here.
Zinsco. The trouble is at the contact rather than inside the mechanism. Great American Insurance's loss-control guide describes it: each breaker grips the bus with an aluminum clip, the bus itself can be aluminum, and over time the clip loosens and the connection corrodes and arcs. A loose connection runs hot. It can weld the breaker to the bus so it no longer trips, and a breaker can look switched off while the circuit is still live. A bad contact is also how a house ends up with outlets that work sometimes and not others.
Challenger. This one is more mixed than its reputation. Challenger came out of the same Sylvania corporate family as Zinsco, and some Challenger breakers have had real problems, including a 1988 replacement program run with the CPSC for one model of GFCI breaker. Insurers often lump Challenger in with Zinsco on their lists. But a lot of later Challenger panels are sound, and the breakers for them are still made today. A Challenger needs to be looked at, not condemned on the label.
How to tell what you have
- The brand is printed on the panel door. Open it and look. Federal Pacific, Zinsco, Sylvania or Challenger, or a label that says Stab-Lok.
- Look at the breakers themselves. Stab-Lok breakers carry the name, and Zinsco breakers have a thin profile that does not match anything sold today.
- Look for effort. If somebody has had to fight a breaker to get it to seat, or if a breaker sits crooked in its slot, the bus underneath it is not gripping any more.
- Look for a missing one. A blank space where a breaker should be, covered over, is often a breaker somebody pulled because it kept tripping. That is a symptom, not a repair.
What Louisiana actually says about it
Nothing, by brand. Louisiana adopts the National Electrical Code statewide, with state amendments on top, and the NEC does not name panel manufacturers. The code regulates what equipment has to do, not who made it, so an inspector in East Baton Rouge is not going to condemn a panel over the name on the door.
What gets written up is the failure. A breaker that will not trip. A bus that has corroded. A panel with no circuit directory. A service disconnect nobody can reach. Those are the things that end up on a correction notice, and they are the same things that go wrong in the panels in this article.
The state is changing code editions right now. The 2020 NEC with Louisiana amendments has been in force since January 1, 2023. On July 7, 2026, the state approved the 2023 NEC and the 2024 International Codes, and they take effect January 1, 2027.
A panel swap is permitted work in Baton Rouge
This is where the city-parish's position actually shows up, and it is in the paperwork rather than in the brand.
The city-parish permit list covers "replacement of electrical meters, disconnects and other service equipment," so a panel change needs a permit and an inspection. The exemptions are narrow and they are the like-for-like jobs: a switch, a receptacle, a light fixture, or a breaker of the same size in the same location. None of that is a panel replacement.
- The permit comes from the city-parish Permit and Inspection Division.
- The inspection. The city inspects the work before the job is closed out.
- Who can do the work. The city requires larger residential jobs to be done by a registered home improvement contractor or a licensed residential contractor. A homeowner can pull a permit on their own house by filing a notarized affidavit claiming exemption from licensure, which the city forwards to the Louisiana State Licensing Board for Contractors.
What the insurance company wants
Do not assume every carrier treats this the same, because they do not. Some will not write or renew a policy on a house with a Federal Pacific or Zinsco panel. Others will write it as long as a licensed electrician inspects and signs off. Others never ask until there is a claim. The four-point inspection is most familiar from Florida, where Citizens requires one on homes more than 20 years old, and carriers elsewhere use them too. Baton Rouge is not Florida, and a homeowner here should not assume the letter they got is the letter their neighbor would get.
Three other things push the same direction:
- A lender appraisal. FHA and VA appraisals look for electrical hazards, and a flagged panel can become a repair that has to be made before closing.
- A sale. A buyer's inspector will find the panel, and work done without a permit raises questions nobody wants to answer at closing.
- The utility. After a service change, Entergy may need the work inspected by the local authority before it will restore power.
What all of them want at the end is the same thing, which is documentation showing a licensed electrician replaced the panel and the work passed inspection. A passed inspection from the city. The permit card. That kind of paper.
What replacement actually involves
A panel swap usually takes most of a day, and the power is off for the duration, so plan it around the refrigerator and anybody working from home.
- A permit first. The city inspects the work when it is done. An unpermitted panel is its own problem at the next sale.
- A decision about size. A 100 amp service was common when these panels went in. A house with central air, a tankless water heater, or a car charger on the horizon may need 200 amp, and making that call during the swap saves doing the work twice.
- The old breakers go away with it. Nothing from a Stab-Lok or Zinsco panel carries over into a modern one, which is most of the point.
Common questions
Can I just replace the breakers and keep the panel? For Federal Pacific and Zinsco, no. On a Zinsco the bus is often the part that has failed, and a new breaker on a corroded bus has the same problem the old breaker did. Replacement breakers for both brands are still sold, but independent testing of replacement Stab-Lok-type breakers found many of them failing to trip as well. Replacing the panel is the fix that also produces the paperwork your insurer is asking for.
The panel has worked fine for forty years. Why now? Because nothing in these panels fails loudly. A breaker that will not trip only shows itself the one time it was supposed to, so it can be bad for years before anyone knows.
Will my insurance drop me if I do nothing? Some will, and some will simply decline to renew, which is the same thing with a deadline attached. If you are in Baton Rouge and you have the letter in hand, call us and we will look at the panel and tell you honestly whether it needs to go or whether your carrier is being cautious.
A photo of the panel label helps us show up prepared, but whether a panel needs to go is something we decide standing in front of it, not over the phone. If you already know you have a Federal Pacific or Zinsco, see our Federal Pacific and Zinsco panel replacement page.